某型飞机平尾轴疲劳断裂失效分析

采用台架试验装置对某型飞机平尾轴进行了疲劳试验,通过断口的观察分析、断口部位的金相分析、硬度检测、有限元结构应力分析,确定了平尾轴的失效模式,并对其断裂失效原因进行了分析。结果表明：平尾轴的断裂性质为疲劳断裂,裂纹源均起源于大轴简体内壁加工刀痕形成的沟槽处,变截面圆弧造成的结构应力集中和粗糙加工刀痕形成的附加应力集中是造成大轴疲劳断裂的主要原因。关键词：平尾轴;疲劳断裂;失效分析;应力集中     

燃烧室压力对潜入式喷管喉衬热应力的影响

为了研究燃烧室压力对固体火箭发动机潜入式喷管热应力影响规律的问题,采用商业流体软件,基于压力求解器,求解了喷管纯气相的流场,确定了燃气温度、压力、壁面对流换热系数;采用有限元软件,依据流场计算的非均布壁面压力与非均布对流换热,求解了燃烧室压力为6 MPa下的潜入式喷管热结构问题;通过地面点火试验验证了仿真模型与数值方法的有效性与准确性;采用相同计算模型与数值方法,求解了在燃烧室压力为9 MPa、12 MPa下的喷管热结构问题,揭示了燃烧室压力对喉衬热应力的影响规律。结果表明:整个工作过程,喉衬环向应力最大值为103.9 MPa,位于内表面,且随时间增大,先增大后减小;喉衬环向拉应力也随时间先增大后减小;随压力增大,对流换热系数增大,喉衬温度升高,喉衬环向拉应力增大,喉衬环向压应力减小。     

Effect of friction stir processing on mechanical properties and heat transfer of TIG welded joint of AA6061 and AA7075

Tungsten inert gas (TIG) welding is the most commonly used joining process for aluminum alloy for AA6061 and AA7075 which are highly demanded in the aerospace engineering and the automobile sector, but there are some defects occur during TIG welding like micro-crack, coarse grain structure, and porosity. To improve these defects, the TIG welded joint is processed using friction stir processing (FSP). This paper presents the effect of friction stir processing on TIG welding with filler ER4043 and ER 5356 for dissimilar aluminum alloy AA6061 and AA7075. The mechanical characterization, finite element formulation and mathematical equations of heat transfer of TIG + FSP welded joints are investigated using ANSYS Fluent software by adjusting process parameters of FSP. The results show that the maximum compressive residual stress 73 MPa was obtained at the fusion zone (FZ) of the TIG weldment with filler ER4043, whereas minimum compressive residual stress 37 MPa was obtained at stir zone (SZ) of the TIG+FSP with filler 5356. The maximum heat flux 5.33 × 106 W/m2 and temperature 515 ℃ have observed at tool rotation 1600 rpm with a feed rate of 63 mm/min. These results give a satisfactory measure of confidence in the fidelity of the simulation     

ORGANISING THE BLUES

While all governments in the region acknowledge the importance of the work of police officers, they seldom take a close look at their working conditions and the nature of police labour. While the situations in Namibia, Zimbabwe, Zambia, Lesotho and Swaziland are different there are commonalities: police management has not changed significantly and neither has police legislation. Key concerns of the officers in the region centre on service conditions and wages. Communicating these concerns to the state is made difficult by the less than democratic approach taken by governments professing to favour democratization. A more democratic workplace for the police is of benefit to the broader community and is a crucial point to bear in mind when attempting to develop community-oriented professional policing.     

基于步进加速寿命试验的制导弹药储存寿命评估

介绍步进应力加速寿命试验原理,通过对制导弹药自动导引头贮存状态和失效机理的分析,确定了加速寿命试验应力和应力水平．假设产品寿命服从威布尔分布,应用极大似然估计和Bayes的方法处理数据,建立制导弹药可靠储存寿命预测模型,并计算得到自动导引头在正常应力水平下的可靠储存寿命．     

悬臂式围护桩受力性状与内力传递特征试验

为研究悬臂式围护桩结构的内力、弯矩、位移和嵌固段的变化规律及特点,结合西宁火车站综合改造工程,对该深基坑支护结构在不同开挖工况条件下悬臂桩的受力性状与内力传递特征进行现场动态测试试验。试验结果表明:悬臂桩的受力特征与理论值有所差异,在实际设计中可对其在配筋方式、混凝土强度设计、嵌固段长度等方面进行优化。试验结果可以有效优化桩身设计,为复杂基坑在开挖过程中的支护结构受力及变形提供参考性依据。     

Influences of different crossing types on dynamic response of underground cavern subjected to ground shock

An intersecting cavern is a common structural form used in underground engineering, and its safety and stability performance directly control the service performance of the whole project. The dynamic re-sponses of the three kinds of crossing type (+-shaped, T-shaped, L-shaped) caverns subjected to ground shock were studied by numerical simulation. The velocity plus force mode boundary setting method was proposed in the coupled static and dynamic analysis of a deep underground cavern. The results show that, among the three types of crossing caverns, the+-shaped cavern is the most significantly affected by the dynamic action, followed by T-shaped, and then L-shaped caverns. The vault settlement, straight wall deformation, vault peak particle velocity, effective plastic strain of surrounding rock, and maximum principal stress and strain at the bottom of the lining of the straight wall increase with the increase of cavern span. The vault settlement, straight wall deformation, effective plastic strain of surrounding rock, and the maximum principal stress and strain at the bottom of lining to the straight wall decrease with the increase of lateral pressure coefficient, and the peak particle velocity at the vault increases. The variation is small compared with the change of cavern span. The influence range of the underground cavern intersection is two cavern diameters from the intersection centre. The bottom of the straight wall at the intersection is the weak part. It is suggested to thicken the support locally to improve the stability of the cavern.     

基于整车虚拟道路行驶试验的车辆零部件疲劳分析

针对现有车辆零部件精确疲劳分析依赖成本高昂的实车试验的问题,提出了一种利用整车虚拟样机仿真分析零部件疲劳寿命的方法。该方法通过在ADAMS/CAR中用整车虚拟样机在虚拟道路模型上进行行驶试验,利用多体系统动力学基于模态坐标的求解特点,使用模态应力恢复技术准确还原出了用于零部件疲劳寿命分析的载荷历程。将该方法应用于某车辆双横臂前悬中的下控制臂,在较短的时间内获得了该零件的预测疲劳寿命、寿命安全系数及危险部位等信息。应用结果表明,该方法可作为汽车设计过程与测试过程中的有效试验手段。     

考虑预紧力与阀杆力的电动截止阀体应力分析

建立了有预紧力的截止阀有限元计算模型,阐述了预紧力单元的原理及分析方法,利用ANSYS程序对截止阀在考虑和不考虑螺栓预紧力及阀杆闭合力作用下的应力进行了计算。结果表明,法兰螺栓预紧力及阀杆闭合力对阀体应力的影响不可忽略。     

通过应力波速测试丁苯橡胶的瞬态模量

运用粘弹性材料的积分型本构关系和应力波理论得出了粘弹性材料瞬态模量的计算式;又以丁苯橡胶作为试验材料设计了一种简便的试验方法,测出了丁苯橡胶的瞬态模量,并与丁苯橡胶的静态弹性模量做了对比。比较表明,丁苯橡胶类粘弹材料静态模量的值远低于瞬态模量值。